Direct TV Manual Auto Tune

The Direct TV Manual Auto Tune feature allows users to automatically scan and program available channels on their Direct TV receiver. This comprehensive guide covers the auto-tuning process, channel management, signal optimization, and troubleshooting for optimal viewing experience. Below are key sections covering setup, operation, and common issues.

1. Auto Tune Overview 2. Initial Setup Requirements 3. Auto Tune Procedure 4. Channel Management 5. Signal Optimization 6. Manual Channel Addition 7. Parental Controls 8. Favorite Channels Setup 9. Software Updates 10. Regulatory Information 11. Troubleshooting

Auto Tune Overview

The Auto Tune feature automatically scans for all available channels in your area and programs them into your Direct TV receiver for easy access.

Feature	Description
Automatic Channel Scan	Scans all available frequencies for active channels
Signal Strength Detection	Measures signal quality for each channel found
Channel Sorting	Automatically organizes channels numerically
Duplicate Detection	Identifies and handles duplicate channel signals
Channel Information	Displays channel names and numbers
Scan Progress Indicator	Shows real-time scanning progress
Failed Channel Log	Records channels with poor signal quality
Auto-save Function	Saves all found channels automatically
Manual Override	Allows manual channel addition if needed
Channel Skip Option	Enables skipping unwanted channels

Initial Setup Requirements

Before starting auto tune, ensure all equipment is properly connected and configured.

Connect satellite dish: Ensure proper alignment and cable connections.
Connect receiver: Use HDMI or component cables to TV.
Power on equipment: Turn on receiver and television.
Check signal strength: Verify adequate signal before starting scan.

IMPORTANT! Ensure satellite dish has clear line of sight to avoid signal obstruction during scanning.

Auto Tune Procedure

Follow these steps to perform automatic channel tuning.

Access menu: Press MENU on remote control.
Select settings: Navigate to SETTINGS or INSTALLATION menu.
Choose auto tune: Select AUTO TUNE or SCAN CHANNELS option.
Start scan: Press OK to begin automatic channel scanning.
Wait for completion: Process may take 5-15 minutes depending on signal.
Save results: System automatically saves all found channels.
Verify channels: Check channel list for completeness.

NOTE: Do not interrupt power during scanning process to avoid corruption.

Channel Management

Channel List: Access via GUIDE button on remote.
Channel Editing: Remove or hide unwanted channels.
Channel Sorting: Arrange channels by number or category.
Channel Lock: Password protect specific channels.
Channel Information: View details by pressing INFO.
Channel Skip: Configure channels to skip during surfing.
Channel Favorites: Create custom favorite channel lists.
Channel Updates: System periodically updates channel information.

Signal Optimization

Optimize signal quality for better channel reception and auto tune results.

Signal Strength Check: Access signal meter in menu to verify quality.

Antenna Alignment: Ensure satellite dish is properly aligned. Cable Inspection: Check for damaged cables or loose connections. Weather Considerations: Account for weather conditions affecting signal. Multiple Receiver Setup: Configure properly for multi-room viewing. Signal Booster: Consider signal amplifier for weak areas.

Manual Channel Addition

Add specific channels manually if auto tune misses them.

Access manual tune: Menu > Settings > Manual Tune.
Enter frequency: Input specific channel frequency.
Scan frequency: Search for channel on entered frequency.
Save channel: Add to channel list if found.
Test channel: Verify channel plays properly.

Tip: Use manual tune for local channels or specialty programming.

Parental Controls

Set parental controls to manage channel access and content restrictions.

Channel Blocking: Block specific channels by rating. Purchase Controls: Restrict pay-per-view purchases. Time Controls: Set viewing time limits. Default Password: 0000 or 1234 (check manual).

Favorite Channels Setup

Create custom favorite channel lists for quick access.

Access favorites: Press GUIDE then FAVORITES.
Create list: Select CREATE NEW FAVORITES LIST.
Add channels: Check boxes next to desired channels.
Save list: Name and save favorite list.
Access quickly: Use FAVORITES button for quick switching.

NOTE: Multiple favorite lists can be created for different users.

Software Updates

Keep receiver software updated for optimal auto tune performance.

Automatic Updates: System checks for updates periodically. Manual Update: Force update in system settings. Update Benefits: Improved channel scanning, bug fixes, new features.

Regulatory Information

FCC Compliance: Meets all federal communications requirements. Copyright: Direct TV and related trademarks property of AT&T. Support: Contact 1-800-DIRECTV or visit directv.com for assistance. Software License: Subject to terms and conditions of service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Auto tune finds no channels	Poor signal/incorrect setup	Check satellite alignment; verify connections; restart receiver.
Channels missing after auto tune	Weak signal/scan interruption	Perform manual channel addition; check signal strength.
Pixelation on channels	Signal interference	Check cable connections; realign dish; check weather conditions.
Auto tune freezes	Software issue	Restart receiver; check for software updates; reset to factory defaults.
Channels out of order	Scanning error	Re-run auto tune; manually reorder channels in settings.

Reset: Menu > Settings > System Reset > Factory Reset (use caution).

Service: 1-800-DIRECTV; directv.com/support