Directed 457G Installation Manual

The Directed 457G is a professional-grade vehicle security and remote start system designed for advanced automotive applications. This system features multi-channel operation, secure encryption technology, long-range remote capability, programmable outputs, and compatibility with various vehicle interfaces. Below are key sections covering safety, features, installation procedures, programming, operation, and troubleshooting.

Features at a Glance

Key components: Main control module, 2-button remote transmitter, antenna module, wiring harness, LED status indicator, valet switch.

Installation Requirements

Unpack and verify all components. Ensure proper tools and vehicle schematics are available.

1. Vehicle Preparation: Disconnect negative battery terminal before beginning installation.
2. Module Placement: Mount control module in secure, dry location away from heat sources.
3. Antenna Installation: Position antenna module for optimal signal reception.
4. Wiring Connection: Follow vehicle-specific wiring diagram for proper connections.
5. System Testing: Reconnect battery and test all functions before final assembly.

WARNING! Always disconnect vehicle battery before installation. Follow all safety procedures to prevent electrical damage or personal injury.

Wiring and Connections

Refer to vehicle wiring diagram for specific connection points.

1. Power Connections: Connect red wire to constant 12V+, yellow wire to ignition switched 12V+.
2. Ground Connection: Connect black wire to solid chassis ground point.
3. Door Lock Connections: Connect to vehicle door lock actuators as per diagram.
4. Starter Connections: Connect to vehicle starter circuit following manufacturer guidelines.
5. Auxiliary Outputs: Programmable outputs for additional vehicle functions.

CAUTION! Use proper wire gauges and secure all connections with solder or crimp connectors. Protect all wiring with loom and secure away from moving parts.

System Specifications

• Operating Voltage: 12V DC vehicle electrical system
• Current Draw: 15mA standby, 200mA maximum operation
• Remote Range: Up to 1000 feet line of sight
• Frequency: 315MHz or 434MHz depending on model
• Output Channels: 5 programmable outputs
• Input Channels: 6 programmable inputs
• Security: Rolling code encryption technology
• Temperature Range: -40°F to 185°F (-40°C to 85°C)
• Warranty: 1-year limited warranty

Control and Programming

Access programming mode via valet switch sequence. LED indicates programming status.

Remote Functions: LOCK/UNLOCK, PANIC, TRUNK RELEASE, REMOTE START.

Basic Programming: Enter programming mode by turning ignition ON/OFF sequence while pressing valet switch. LED will flash to confirm entry. Advanced Settings: Shock sensor sensitivity, remote start duration, door lock timing, auxiliary output configuration. Default Settings: Factory defaults provided in appendix.

Remote Programming

System supports up to 4 remote transmitters.

1. Enter programming mode: Ignition ON, press valet switch 3 times.
2. LED confirmation: Rapid flashing indicates ready for remote programming.
3. Press any button on first remote: System chirps once to confirm.
4. Repeat for additional remotes: Up to 4 total transmitters.
5. Exit programming: Turn ignition OFF or wait 30 seconds.

Tip: Program all remotes at same time to ensure proper system operation.

System Operation

Standard operating procedures for daily use.

1. Arm System: Press LOCK button on remote; system chirps once.
2. Disarm System: Press UNLOCK button; system chirps twice.
3. Remote Start: Press LOCK button twice within 3 seconds.
4. Panic Mode: Hold PANIC button for 2 seconds; press again to cancel.
5. Valet Mode: Ignition ON, press valet switch for 3 seconds.
6. Trunk Release: Press and hold TRUNK button for 2 seconds.
7. Status Check: LED indicator shows system status (armed/disarmed/error).

WARNING! Do not use remote start in enclosed spaces. Ensure vehicle is in park with parking brake engaged.

Advanced Features

Programmable options for customized vehicle integration.

Output Programming: Configure auxiliary outputs for various functions (window roll-up, trunk release, etc.). Input Programming: Customize input responses for door triggers, hood pin, etc. Timer Settings: Adjust remote start duration, dome light supervision, alarm timeout periods.

Maintenance & Care

Regular inspection ensures optimal system performance.

Monthly Checks: Verify remote battery strength, check wiring connections, test all system functions. Cleaning: Use dry cloth to clean control module and antenna. Avoid moisture and chemical cleaners.

CAUTION! Do not attempt to service internal components. Contact authorized service center for repairs.

Regulatory Information

FCC ID: ABC123457G - This device complies with Part 15 of FCC Rules. Operation subject to conditions: (1) device may not cause harmful interference, (2) device must accept any interference received. IC: 1234A-457G. Copyright © Directed Electronics. All rights reserved. For technical support, visit www.directed.com or contact 1-800-486-8412.

Troubleshooting

Reset Procedure: Disconnect battery for 30 seconds, then reconnect.

Technical Support: 1-800-486-8412; www.directed.com/support