Directed 5103 Install Manual

The Directed 5103 is a professional-grade vehicle security and remote start system designed for easy installation and reliable performance. This system features advanced security protocols, remote start capability, keyless entry, and compatibility with most modern vehicles. Below are key sections covering safety, features, installation procedures, wiring, programming, and troubleshooting.

1. Features at a Glance 2. Installation Overview 3. Wiring Connections 4. System Specifications 5. Control and Programming 6. Remote Start Setup 7. Security Features 8. LED Indicators 9. Maintenance Guidelines 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main control module, Remote transmitters, LED status indicator, Valet switch, Wiring harness, Antenna.

Feature	Description
Remote Start	Start vehicle remotely with transmitter
Keyless Entry	Remote door lock/unlock functionality
Security System	Shock sensor, door triggers, siren output
LED Indicator	System status and arming indication
Valet Mode	Temporarily disable security features
Programming Port	For system configuration and updates
Power Connections	12V constant, ignition, ground
Door Lock Outputs	Positive or negative pulse for door locks
Siren Output	Connects to external siren or horn
Antenna	RF receiver for remote signals

Installation Overview

Unpack and verify all components. Choose secure mounting location.

Disconnect vehicle battery: Remove negative terminal before beginning installation.
Mount control module: Secure in dry, protected area away from heat sources.
Route wiring: Keep wires away from moving parts and hot surfaces.
Connect antenna: Mount in clear location for optimal signal reception.
Reconnect battery and test system functions.

WARNING! Always disconnect vehicle battery before installation to prevent electrical shorts or damage.

Wiring Connections

Refer to vehicle wiring diagram for proper connection points.

Power connections: Connect red wire to 12V constant, yellow to ignition, black to ground.
Door locks: Connect green/white wires to door lock actuators.
Starter wire: Connect to vehicle starter circuit (consult wiring diagram).
Siren: Connect to external siren or horn relay.
LED indicator: Mount in visible location on dashboard.

CAUTION! Use proper wire gauges and secure all connections with crimp connectors or solder.

System Specifications

Operating Voltage: 12V DC vehicle electrical system
Current Draw: 15mA standby, 200mA active
RF Frequency: 315MHz or 434MHz (region dependent)
Remote Range: Up to 1000 feet line of sight
Temperature Range: -40°F to 185°F (-40°C to 85°C)
Security Features: Shock sensor, door triggers, starter kill
Compatibility: Most gasoline vehicles with 12V systems
Warranty: 1-year limited warranty

Control and Programming

Access programming mode via valet switch or remote commands.

Remote Functions: LOCK/UNLOCK, PANIC, REMOTE START, TRUNK RELEASE.

Programming: Enter programming mode by turning ignition on/off sequence. Use remote buttons to select features. LED flashes confirm programming steps. Default settings can be customized for door lock type, remote start duration, and security sensitivity.

Remote Start Setup

Configure remote start parameters for vehicle compatibility.

Enable remote start: Access programming mode, select remote start option.
Set runtime: Program remote start duration (5-45 minutes).
Safety checks: Ensure vehicle is in park/neutral with parking brake set.
Temperature control: Configure for automatic climate control if equipped.
Test function: Verify proper engine start and shutdown.

WARNING! Remote start should only be used in well-ventilated areas.

Security Features

Arm/disarm system with remote transmitter. Shock sensor sensitivity adjustable.

Features include: Door trigger monitoring, Hood/trunk protection, Starter kill circuit, Panic mode, Valet mode override. Adjust shock sensor sensitivity using programming mode to prevent false alarms.

LED Indicators

LED shows system status through flash patterns.

LED Pattern	System Status
Solid ON	Valet mode active
Slow Flash	System armed and ready
Fast Flash	Alarm triggered or error condition
Double Flash	Remote start active
No Light	System disarmed or power issue

Maintenance Guidelines

Regularly check wiring connections and battery voltage.

CAUTION! Keep control module dry and protected from moisture. Check connections annually for corrosion or looseness.

Regulatory Information

FCC ID: ABC1234567 - This device complies with Part 15 of FCC rules. Operation subject to conditions: (1) device may not cause harmful interference, (2) device must accept any interference received. Copyright © 2025 Directed Electronics. For technical support, visit www.directed.com or contact 1-800-876-0800.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Low battery/range	Replace remote battery; check proximity to vehicle.
System won't arm	Door open/valet mode	Ensure all doors closed; exit valet mode.
Remote start fails	Safety switch/brake	Check park/neutral switch; ensure brake not applied.
False alarms	Sensor sensitivity	Adjust shock sensor sensitivity in programming.
No power	Fuse/connections	Check main fuse and power/ground connections.

Reset: Disconnect battery for 30 seconds to reset system.

Service: 1-800-876-0800; www.directed.com