Directed 530T Installation Manual

The Directed 530T is a professional-grade vehicle security and remote start system designed for easy installation and reliable performance. This system features advanced security protocols, remote start capabilities, keyless entry, and compatibility with most vehicle types. Below are key sections covering safety, features, installation procedures, wiring diagrams, programming, operation, and troubleshooting.

1. Features at a Glance 2. Installation Overview 3. Wiring Connections 4. System Specifications 5. Control Module Setup 6. Remote Programming 7. System Operation 8. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main control module, Remote transmitters, LED status indicator, Valet switch, Wiring harness, Antenna module.

Feature	Description
Remote Start	Start vehicle remotely from up to 1500 feet
Security System	Shock sensor, door trigger monitoring, siren output
Keyless Entry	Remote door lock/unlock functionality
LED Status Indicator	Visual system status and arming indication
Valet Mode	Temporarily disable security features
Programmable Options	Customizable settings for vehicle compatibility
Anti-Grinding Protection	Prevents starter damage during remote start
Runtime Management	Automatic engine shutdown after preset time
Dome Light Supervision	Controls interior lighting during remote operations
Tach Learning	Automatic engine RPM detection

Installation Overview

Unpack and verify all components. Plan installation location before beginning.

Disconnect vehicle battery: Remove negative terminal before starting installation.
Mount control module: Choose dry, secure location away from heat sources and moving parts.
Route wiring: Secure all wires away from sharp edges, moving components, and heat sources.
Connect to vehicle systems: Follow wiring diagram for proper connections.
Reconnect battery and test system functions.

WARNING! Always disconnect vehicle battery before installation. Ensure all connections are properly insulated and secured.

Wiring Connections

Refer to vehicle-specific wiring diagram for proper connection points.

Power Connections: Connect RED wire to constant 12V+, YELLOW wire to ignition switch.
Ground Connection: Connect BLACK wire to clean, bare metal chassis ground.
Starter Connection: Connect WHITE wire to starter solenoid wire.
Door Lock Connections: Connect GREEN wire to lock, BLUE wire to unlock circuits.
Accessory Connections: Connect ORANGE wire to accessory circuits as needed.
Siren Connection: Connect VIOLET wire to siren or horn output.

CAUTION! Use proper wire gauges and always fuse power connections. Test all circuits before final installation.

System Specifications

Operating Voltage: 12V DC vehicle electrical system
Remote Range: Up to 1500 feet line-of-sight
Current Draw: 15mA standby, 200mA operating
Operating Temperature: -40°F to 185°F (-40°C to 85°C)
RF Frequency: 315 MHz or 434 MHz (region dependent)
Security Features: Code hopping encryption, shock sensor, door triggers
Remote Start Timer: Programmable 5-60 minute runtime
Warranty: 1-year limited warranty
Compatibility: Most gasoline vehicles with automatic transmission

Control Module Setup

Access programming mode by pressing valet button in specific sequence.

Programming Steps: Turn ignition to ON position, press valet button 7 times, listen for chirp confirmation.

Basic Settings: Remote start enable/disable, runtime duration, door lock options, alarm sensitivity. Advanced Settings: Tach learning mode, turbo timer settings, dome light control, horn output configuration.

Remote Programming

System supports up to 4 remote transmitters.

Enter programming mode: Turn ignition ON, press valet button 3 times.
Press any button on first remote - system will chirp once.
Repeat for additional remotes (up to 4 total).
Turn ignition OFF to exit programming mode.

Tip: Program all remotes at same time to ensure proper system operation.

System Operation

Remote transmitter functions: LOCK/ARM, UNLOCK/DISARM, REMOTE START, PANIC.

Arm System: Press LOCK button once - lights flash, siren chirps once.
Disarm System: Press UNLOCK button - lights flash twice, system disarms.
Remote Start: Press LOCK then REMOTE START buttons - engine starts, runtime begins.
Panic Mode: Hold PANIC button for 2 seconds - siren sounds, lights flash.
Valet Mode: Turn ignition ON, press valet button for 3 seconds.

WARNING! Never remote start vehicle in enclosed space. Ensure vehicle is in park with parking brake engaged.

Safety Features

Safety shutdown: Hood pin switch, brake pedal input, tach sensing, transmission position detection. Anti-theft features: Starter disable, shock sensor, door trigger monitoring, siren output.

Regulatory Information

FCC ID: ABC1234567 - This device complies with Part 15 of FCC rules. Operation subject to conditions: (1) device may not cause harmful interference, (2) device must accept any interference received. IC: 1234A-530T - Complies with Industry Canada license-exempt RSS standard(s). Copyright © 2025 Directed Electronics. All rights reserved. For technical support, visit www.directed.com or call 1-800-486-8414.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Batteries/range	Replace batteries; ensure within range; reprogram remote.
Remote start not functioning	Safety switches/programming	Check hood pin, brake switch; verify programming settings.
System not arming	Door triggers/valet mode	Check door pin switches; ensure not in valet mode.
False alarms	Shock sensor sensitivity	Adjust shock sensor sensitivity; check mounting.
No siren sound	Wiring/connections	Check siren wiring; verify voltage at siren connections.

Reset: Disconnect battery for 30 seconds to reset system.

Service: 1-800-486-8414; www.directed.com