Directed Electronics 5305L Installation Manual

The Directed Electronics 5305L is a professional-grade vehicle security system featuring remote start capability, keyless entry, shock sensor, and anti-carjacking protection. This system includes a 2-way LCD remote control, siren, hood pin switch, LED status indicator, and all necessary wiring harnesses. Below are comprehensive sections covering installation procedures, wiring diagrams, programming instructions, and troubleshooting guidelines.

1. System Components 2. Pre-Installation Checklist 3. Wiring Connections 4. Remote Start Installation 5. Security Features Setup 6. Programming Procedures 7. Remote Control Operation 8. System Testing 9. Troubleshooting Guide 10. Technical Specifications

System Components

Complete package includes: Main control module, 2-way LCD remote control, siren with bracket, hood pin switch, LED status indicator, shock sensor, wiring harnesses, and installation accessories.

Component	Description
Main Control Module	Central processing unit with 12-pin connector
2-Way LCD Remote	Displays system status with 3000ft range
Siren	110dB output with mounting bracket
Hood Pin Switch	Prevents remote start when hood is open
LED Status Indicator	Blue LED shows system arming status
Shock Sensor	Adjustable sensitivity for impact detection
Wiring Harnesses	Pre-wired connectors for vehicle integration
Valet Switch	Temporarily disables security features
Relays	For door lock and starter control
Installation Manual	Complete setup and programming guide

Pre-Installation Checklist

Before beginning installation, verify all components and prepare the vehicle.

Disconnect vehicle battery negative terminal
Test all vehicle electrical systems (locks, lights, ignition)
Identify vehicle wiring locations and colors
Plan module mounting location (under dashboard)
Route wiring away from moving parts and heat sources
Test remote control battery level

WARNING! Always disconnect battery before installation. Failure to do so may cause electrical damage or injury.

Wiring Connections

Connect all wires according to vehicle-specific wiring diagram.

Power Connections: Red to constant 12V+, Black to chassis ground
Ignition Wires: Orange to ignition switch, Pink to accessory
Starter Wire: Yellow to starter solenoid
Door Lock Wires: Green/White to lock, Brown/White to unlock
Parking Light Wire: Blue to parking light positive
Siren Wire: Red/Black to siren positive
Hood Pin: Purple to normally closed hood switch

CAUTION! Use proper wire taps and solder all connections. Test each circuit before final installation.

Remote Start Installation

Remote start requires additional safety precautions and specific wiring.

Connect tachometer wire to vehicle tach signal
Install hood pin switch and connect to purple wire
Connect brake switch wire to brake pedal switch
Set remote start timer (default 15 minutes)
Program vehicle-specific parameters
Test remote start with vehicle in park/neutral

WARNING! Remote start will not engage if hood is open, brake is pressed, or vehicle is in gear.

Security Features Setup

Configure security system parameters for optimal protection.

Shock Sensor: Adjust sensitivity using potentiometer on sensor
Anti-Carjacking: Enable in programming mode (feature 5)
Panic Mode: Press and hold remote panic button for 3 seconds
Valet Mode: Disables security features for service
Passive Arming: System arms automatically after 30 seconds
Door Trigger: Monitors all door positions

Programming Procedures

Access programming mode by turning ignition ON/OFF sequence.

Enter Programming: Turn ignition ON, press valet button 7 times
Select Feature: Use remote buttons to scroll through options
Set Parameters: Press lock/unlock to change settings
Exit Programming: Turn ignition OFF and test features
Remote Programming: Hold buttons 1+4 for remote sync
Door Lock Timing: Adjust for vehicle-specific requirements

Note: Programming changes take effect immediately. Test all functions after programming.

Remote Control Operation

2-way LCD remote provides complete system control and status feedback.

Button	Function	Operation
Lock	Arm System	Press once to lock doors and arm
Unlock	Disarm System	Press once to unlock driver door
Remote Start	Start Engine	Press twice to remote start
Panic	Alarm Trigger	Hold for 3 seconds
Trunk	Trunk Release	Press and hold for 2 seconds
Status	System Check	Displays arming status and alerts

System Testing

Thoroughly test all system functions before completing installation.

Arm/disarm system using remote control
Test remote start from minimum 100 feet
Verify door lock/unlock operation
Test shock sensor by tapping vehicle
Confirm hood pin prevents remote start
Check LED status indicator operation
Test panic mode activation
Verify siren sounds during alarm

Important: Document all test results and adjust settings as needed.

Troubleshooting Guide

Problem	Possible Cause	Solution
Remote not working	Low battery/range	Replace battery; check range limitations
No remote start	Hood pin/brake switch	Check hood pin connection; verify brake switch
False alarms	Shock sensitivity	Adjust shock sensor sensitivity lower
Doors not locking	Wire connection/timing	Check door lock wires; adjust lock timing
No siren sound	Siren wire/power	Verify siren connection and ground
LED not flashing	Programming/connection	Check LED wire; verify programming mode

Technical Specifications

Operating Voltage: 12V DC negative ground
Current Draw: 15mA standby, 200mA alarm
Remote Range: Up to 3000 feet (2-way)
Siren Output: 110dB at 1 meter
Operating Temperature: -40°F to 185°F (-40°C to 85°C)
Remote Battery: CR2032 (2-way remote)
Shock Sensor: 2-stage adjustable sensitivity
Warranty: 1-year limited warranty

Support: Directed Electronics Technical Support: 1-800-527-8495