directed electronics inc 2101l install manual

The Directed Electronics Inc 2101L is a professional-grade vehicle security system with advanced features including remote start capability, keyless entry, shock sensor, LED status indicator, valet mode, and programmable options. The system operates on 12V DC vehicle power and includes a 2-button remote transmitter. Below are key sections for installation, wiring, programming, operation, and troubleshooting.

Features at a Glance

Key components: Main control module, 2-button remote transmitter, shock sensor, LED status indicator, wiring harness, and mounting hardware.

Installation Requirements

Unpack and inspect all components before installation. Ensure vehicle battery is fully charged.

1. Vehicle Compatibility: Check vehicle wiring diagram for proper connections.
2. Mounting Location: Install control module in dry, protected area under dashboard.
3. Shock Sensor Placement: Mount on solid metal surface away from moving parts.
4. LED Indicator: Install in visible location on dashboard.
5. Antenna Placement: Route antenna wire away from metal obstructions.

WARNING! Disconnect vehicle battery before beginning installation. Professional installation recommended.

Wiring Connections

Refer to vehicle-specific wiring diagram for proper connection points.

1. Power Connections: Connect RED wire to constant 12V+, BLACK wire to chassis ground.
2. Ignition Input: Connect WHITE wire to ignition switch output.
3. Starter Output: Connect YELLOW wire to starter solenoid trigger.
4. Door Lock/Unlock: Connect GREEN and BLUE wires to power lock system.
5. Door Triggers: Connect VIOLET wires to door pin switches.
6. Siren Output: Connect ORANGE wire to optional siren/horn.
7. Parking Light Output: Connect BROWN wire to parking light circuit.

CAUTION! Use proper wire gauges and secure all connections with solder or crimp connectors.

System Specifications

• Operating Voltage: 12V DC vehicle electrical system
• Current Draw: 15mA standby, 200mA alarm active
• Remote Range: Up to 500 feet line of sight
• RF Frequency: 315 MHz or 434 MHz (region specific)
• Shock Sensor: 2-stage sensitivity adjustment
• Operating Temperature: -40°F to 185°F (-40°C to 85°C)
• Remote Battery: 12V 23A alkaline battery
• Warranty: 1-year limited warranty

Control Module Setup

Access programming mode by turning ignition ON/OFF sequence and pressing valet button.

Programming Steps: Enter programming mode, use remote buttons to select options, exit programming mode to save settings.

Basic Settings: Passive/active arming, door lock pulse timing, remote start duration, shock sensor sensitivity, panic mode enable/disable. Advanced Settings: Turbo timer configuration, dome light supervision, anti-grinding protection, tachometer learning mode.

Remote Programming

System supports up to 4 remote transmitters.

1. Enter programming mode: Turn ignition ON, press and hold valet button until LED flashes.
2. Press any button on first remote - system will chirp once.
3. Repeat for additional remotes (up to 4 total).
4. Turn ignition OFF to exit programming mode.

Tip: Program all remotes at the same time as previously programmed remotes will be erased.

Operation Instructions

Basic remote functions and system operation procedures.

1. Arming: Press LOCK button once - system arms, doors lock, LED flashes.
2. Disarming: Press UNLOCK button once - system disarms, doors unlock.
3. Remote Start: Press LOCK button twice within 3 seconds - engine starts.
4. Panic Mode: Press and hold both buttons for 2 seconds - alarm activates.
5. Valet Mode: Turn ignition ON, press and hold valet button for 5 seconds.
6. Trunk Release: Press and hold UNLOCK button for 2 seconds (if equipped).
7. Silent Arm: Press LOCK then UNLOCK buttons - arms without chirp.

WARNING! Do not use remote start in enclosed spaces due to carbon monoxide risk.

Security Features

Shock Sensor: Adjust sensitivity using potentiometer on sensor module. Valet Mode: Disables security features for service/maintenance. Anti-Theft: Starter disable relay prevents unauthorized starting. Code Hopping: Rolling code technology prevents code grabbing.

Maintenance & Care

Regularly check remote battery, inspect wiring connections, and test system functionality.

CAUTION! Keep control module dry and protected from moisture. Do not expose to extreme temperatures.

Regulatory Information

FCC Part 15: This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. IC: Complies with Industry Canada license-exempt RSS standard(s). Copyright © Directed Electronics, Inc. All rights reserved. For technical support, contact 1-800-438-5027 or visit www.directed.com.

Troubleshooting

Reset: Disconnect battery for 30 seconds to reset system.

Service: 1-800-438-5027; www.directed.com