Directed Electronics Installation Manual

Directed Electronics specializes in automotive security and remote start systems, offering professional-grade products for vehicle protection and convenience. This manual covers installation procedures, wiring diagrams, programming steps, and troubleshooting for Directed Electronics security systems, remote starters, and related accessories. Below are key sections for safety guidelines, product overview, installation steps, programming, operation, and technical support.

1. Product Overview 2. Safety Precautions 3. Installation Requirements 4. Wiring Connections 5. Programming Steps 6. System Operation 7. Troubleshooting 8. Technical Specifications 9. Warranty Information

Product Overview

Directed Electronics systems include main control module, remote transmitter, antenna, wiring harness, and optional accessories like shock sensors and backup batteries.

Component	Description
Control Module	Main brain of the security/remote start system
Remote Transmitter	2-way or 1-way remote for arming/disarming and remote start
Antenna Module	Receives signals from remote transmitter
Wiring Harness	Pre-wired connectors for vehicle integration
Shock Sensor	Detects impacts and vibrations
LED Indicator	Shows system status and arming mode
Siren	Audible alarm for security breaches
Backup Battery	Powers system if main vehicle battery is disconnected

Safety Precautions

Follow these safety guidelines during installation to prevent damage to vehicle electronics and ensure personal safety.

Disconnect vehicle battery negative terminal before beginning installation.
Use proper tools and protective equipment when working with electrical systems.
Route wiring away from moving parts, heat sources, and sharp edges.
Secure all connections with proper connectors and electrical tape.
Test all vehicle functions after installation before final reassembly.

WARNING! Incorrect installation may damage vehicle electronics or cause safety hazards. Professional installation recommended.

Installation Requirements

Gather necessary tools and materials before beginning installation.

Basic hand tools: screwdrivers, pliers, wire cutters/strippers
Multimeter for voltage testing
Electrical tape, wire ties, and connectors
Vehicle wiring diagram specific to make/model/year
Mounting hardware and double-sided tape
Test light for circuit verification

CAUTION! Ensure vehicle is parked in safe, well-ventilated area with parking brake engaged.

Wiring Connections

Power Connections: Connect red wire to constant 12V+, yellow wire to ignition-switched 12V+
Ground Connection: Connect black wire to solid chassis ground point
Door Lock Wires: Connect to vehicle door lock actuators (consult vehicle wiring diagram)
Starter Wire: Connect to vehicle starter circuit (typically yellow at ignition harness)
Accessory Wires: Connect to accessory circuits for remote start functionality
Parking Light Wire: Connect to vehicle parking light circuit for visual confirmation
Hood Pin Switch: Install safety switch to prevent remote start with hood open
Brake Wire: Connect to brake light switch for safety shutdown

Programming Steps

System programming varies by model. General programming procedure:

Enter programming mode: Turn ignition key to ON position, then press valet button 3 times
LED will flash to indicate programming mode active
Use remote transmitter buttons to select features and options
Common programmable features: remote start duration, door lock/unlock options, alarm sensitivity
Exit programming mode: Turn ignition key to OFF position
Test all programmed features to ensure proper operation

Note: Refer to specific model programming guide for detailed feature codes and options.

System Operation

Basic operation procedures for Directed Electronics security and remote start systems.

Remote Functions: LOCK/ARM, UNLOCK/DISARM, PANIC, REMOTE START, TRUNK RELEASE

Security Features: Arm/disarm with remote, shock sensor activation, siren output, LED status indicator, valet mode. Remote Start Features: Engine start/stop, runtime adjustment, temperature control (if equipped), safety shutdown conditions. Additional Features: Silent arm/disarm, passive arming, starter disable, programmable outputs.

Troubleshooting

Common installation and operation issues with corrective actions.

Symptom	Possible Cause	Corrective Action
System not powering on	Power/ground connections	Check 12V+ and ground connections; verify fuse integrity
Remote not working	Battery/range/programming	Replace remote battery; check programming; reduce interference
Remote start not engaging	Safety switches/wiring	Check hood pin, brake, and neutral safety switches; verify starter wire connection
False alarms	Sensor sensitivity	Adjust shock sensor sensitivity; check for loose connections
Doors not locking/unlocking	Wiring/polarity	Verify door lock wire connections; check polarity reversal module if needed

Reset Procedure: Disconnect battery for 30 seconds to reset system if experiencing persistent issues.

Technical Specifications

Operating Voltage: 12V DC vehicle electrical system
Current Draw: Standby: 15mA, Alarm: 500mA, Remote Start: Varies by vehicle
Operating Range: Up to 1/4 mile (2-way remote), Up to 1,000 feet (1-way remote)
RF Frequency: 315MHz or 434MHz depending on model
Temperature Range: -40°F to 185°F (-40°C to 85°C)
Warranty: 1-year limited warranty from date of purchase
Compatibility: Most gasoline vehicles; check specific model compatibility for diesel and hybrid vehicles

Warranty Information

Directed Electronics products are covered by a limited warranty against defects in materials and workmanship. Warranty registration required within 30 days of installation. Professional installation recommended to maintain warranty coverage. Contact customer service for warranty claims and technical support.

Customer Support: 1-800-486-8412; www.directed.com

Service Centers: Authorized installation centers available nationwide