DIRECTV Wireless Video Bridge WVBR0-25 Manual

The DIRECTV Wireless Video Bridge WVBR0-25 is a wireless connectivity solution that enables wireless transmission of HD video signals between DIRECTV receivers and compatible devices. It supports 1080p HD video quality, operates on 5GHz frequency band, features easy setup with WPS pairing, LED status indicators, and compatibility with Genie mini clients. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Wireless bridge unit, Power adapter, Ethernet port, WPS button, Status LEDs, Reset button.

Installation

Unpack and inspect contents. Place in central location for optimal wireless coverage.

1. Connect to power: Plug power adapter into wall outlet and bridge unit.
2. Connect to receiver: Use Ethernet cable to connect bridge to Genie mini client.
3. Position unit: Place in open area away from obstructions and interference sources.
4. Ensure proper ventilation: Keep at least 2 inches clearance around unit.

WARNING! Do not place near heat sources or in humid environments. Ensure stable surface placement.

First-Time Setup

Power on bridge; observe LED indicators for status.

1. Power up: Connect power adapter; Power LED should illuminate solid green.
2. Wireless pairing: Press WPS button on bridge and main receiver within 2 minutes.
3. Check connection: Wireless LED should turn solid when paired successfully.
4. Verify operation: Check receiver for wireless connection status in system menu.

CAUTION! Keep away from microwave ovens and other 5GHz interference sources during setup.

Specifications

• Wireless Standard: 5GHz 802.11ac
• Video Support: Up to 1080p HD
• Operating Frequency: 5.15-5.85 GHz
• Ethernet Port: 10/100 Mbps
• Power Requirements: 12V DC, 1A
• Operating Range: Up to 50 feet indoors
• Security: WPA2 encryption
• Dimensions: 4.7 x 2.8 x 1.2 inches
• Weight: 0.3 lbs
• Operating Temperature: 32°F to 104°F (0°C to 40°C)

Controls and Indicators

Front Panel: Power LED (green), Wireless LED (blue), Ethernet LED (amber).

Buttons: WPS button (pairing), Reset button (factory reset).

LED Status: Power LED solid = normal operation, blinking = booting; Wireless LED solid = connected, blinking = pairing mode; Ethernet LED solid = connected, off = no connection.

Connecting Devices

Compatible with DIRECTV Genie mini clients and supported receivers.

1. Turn off all devices before connecting.
2. Connect Ethernet cable from bridge to receiver Ethernet port.
3. Power on bridge first, then receiver.
4. Wait for LED indicators to stabilize before proceeding.

Tip: Use quality Ethernet cables for reliable connections. Avoid cable runs longer than 100 feet.

Wireless Pairing

WPS pairing for easy wireless setup.

1. Initiate pairing: Press WPS button on bridge - Wireless LED will blink.
2. Complete pairing: Press WPS on main receiver within 2 minutes.
3. Wait for connection: Wireless LED turns solid when paired successfully.
4. Verify connection: Check receiver menu for wireless status.
5. Manual setup: Use receiver network settings for manual configuration if needed.

WARNING! Do not interrupt power during pairing process. Ensure devices are within range.

Network Features

Wireless bridge functionality for whole-home DVR access. Supports multiple mini clients. Network diagnostics available through receiver menu.

Care & Maintenance

Unplug before cleaning. Use dry, soft cloth only; no liquids or cleaning solutions.

CAUTION! Do not block ventilation openings. Keep away from direct sunlight and moisture.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © DIRECTV. For support, visit www.directv.com or contact 1-800-531-5000. This device complies with part 15 of the FCC Rules.

Troubleshooting

Reset: Hold reset button for 10 seconds to restore factory defaults.

Service: 1-800-531-5000; www.directv.com